CubeCell GPS-6502 US915 (HTCC-AB02S)

Description
Specifications
Show Reviews
Size Chart

The Heltec CubeCell 6502 (AB02S) IoT LoRaWAN + GPS module can be used in any asset tracking or mapping project. With an ultra low-power design and an onboard solar energy management system that can directly connect with a 5.5~7V solar panel.

Features

CubeCell GPS-6502 Arduino-Compatible
LoRaWAN US 915 Mhz
CE and FCC certification
Based on ASR6052, , ASR Microelectronics ASR605x series is highly intergrated and ultra low power SOC based on the PSoC 4000 series MCU (ARM Cortex M0+ Core) and Semtech SX1262 transceiver
LoRaWAN 1.0.2 support
Ultra low power design, 50uA in deep sleep
Onboard solar energy management system, can directly connect with a 5.5~7V solar panel
Onboard SH1.25-2 battery interface, integrated lithium battery management system (charge and discharge management, overcharge protection, battery power detection, USB / battery power automatic switching)
Micro USB interface with complete ESD protection, short circuit protection, RF shielding, and other protection measures
Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing
Good impedance matching and long communication distance
Uses Air530 GPS module, GPS / Beidou Dual-mode position system support
Onboard 0.96-inch 128*64 dot matrix OLED display, which can be used to display debugging information, battery power, and other information

Developing on the Helium Network

The developer documents at the Helium website is top notch. They provide you everything you need to know to get started. Head over to learn how to set up your CubeCell with the Helium Console.

Technical Parameters

Source	Parameter
MCU	ASR6502 (48 MHz ARM^® Cortex^® M0+ MCU, 128KB FLASH, 16KB SRAM )
LoRa Chip	ASR6502 (Internal assembled Semtech^® LoRa^® Transceiver SX1262)
LoRa working band	US_902_928
LoRa maximum output power	22 ± 1dB
Hardware resources	UART x 2; SPI x 1; I2C x 1; SWD x 1; ADCx 3; COMP x 1
	12 – bits ADC; 8 – channel DMA engine
	14 x GPIO
FLASH	128KB internal FLASH
Interface	Micro USB x 1; LoRa (IPEX) x 1
Size	55.9 x 27.9 x 9.5 mm
USB-UART bridge	CP2102
Battery Type	3.7V Lithium (SH1.25 x 2 socket)
Battery detection circuit	√
External device power control（Vext）	√
Low power design	Deep Sleep 50uA

Electrical characteristics

Electrical characteristics	condition	Minimum	Typical	Maximum
Power Supply	USB powered (≥500mA)	4.7V	5V	6V
	Lithium powered（≥250mA）	3.3V	3.7V	4.2V
	3.3V（pin）powered（≥150mA）	2.7V	3.3V	3.5V
	5V（pin）powered（≥500mA）	4.7V	5V	6V
Power consumption(mA)	LoRa Rx Mode		10mA
	LoRa 10dBm output		70mA
	LoRa 14dBm output		90mA
	LoRa 17dBm output		100mA
	LoRa 20dBm output		105mA
	Sleep Mode (USB powered)		9.6mA
	Sleep Mode (VBAT/battery powered)		56uA
	Sleep Mode (3.3V header powered)		50uA
Output	3.3V pin output			500mA
	5V pin output （USB powered only）		Equal to the input current
	External device power control (Vext 3.3V）			350mA

google_product_category:: 275
condition:: new
google_product_category:: Electronics > Networking > Concentrators & Multiplexers
custom_product:: true
vitalsRpk:: 1647557387

Write a Review

0 Reviews Hide Reviews Show Reviews